MVA Remote Vibration Analysis Services

-



Introduction

I am providing this cost-effective unique Vibration Analysis Service due to an injury from a motor vehicle accident and now need to work from home.

Robert has 24 years of experience as a Vibration Analyst in the Mining, Timber and Food industries. He is the owner of Midwest Vibration Analysers 

 Robert has held roles as Maintenance Supervisor, Plant Inspector (Oil & gas) Predictive Systems Analyst, Maintenance Training coordinator, Reliability Supervisor, Reliability Superintendent, and Condition Monitoring Technical Specialist

Please check Roberts's Linkedin Profile for recommendations and endorsements: https://www.linkedin.com/in/robert-smith-4a43a869/

 Why Vibration Analysis?

Every factory or process plant has rotating machinery like pumps, motors, gearboxes other types of process equipment. All these types of equipment incorporate shafts, couplings and bearings. As bearings and couplings wear, shafts go out of alignment and structural looseness occurs and vibration starts to increase eventually leading to equipment failure and downtime.

The ideal way to have a Vibration Analysis Service

This is ideal for production facilities with no vibration experts on site.

Cost-effective for initial troubleshooting support for routine analysis

Customers simply collect vibration data and I will analyze the data via VPN if the company IT policy allows it.

If a company has a remote Vibration System Installed such as Vibcloud or another brand then I can also analyze this data.

If you are using a Commtest Vibration Analyzer and Ascent Software and require assistance or a second opinion on the analysis I am available to assist. Data can be sent to me via email

The vibration data will be analyzed to ISO 10816-7:2009 and sound recommendations are given.

Flexible service

The program is flexible to suit customer needs. Critical and auxiliary machines can be added at the customer's discretion to fulfil maintenance strategy requirements.

Competitive: $40 US/hour

Contact:   robbieccs@gmail.com

Alternative email robertmva@yahoo.com.au

Cell Number: +63 9917895346

WhatsApp:+63 9677512891


Comments

Post a Comment

Popular posts from this blog

Vibration data for Shaft Misalignment - Angular and Offset

-
Image
  Vibration Data for Shaft  Misalignment  Offset/Parallel Misalignment 1X,2X,3X & sometimes 4X & 5X in the radial direction at Motor Running Speed, RPM Angular Misalignment: 1X & 2XRPM in the axial direction. 1X,2X & sometimes 3X in the radial direction. This can depend on the type of coupling in service. Offset/Parallel Misalignment The Centerlines are parallel but offset.  Offset Misalignment Spectrum. Be aware 3X & 4X RPM also be present. Note the 180 deg out of phase across the Coupling This is why phase measurements are needed to help confirm parallel misalignment. The 2X RPM is usually higher than 1X RPM. Readings taken radially in the horizontal and vertical planes should be similar. Angular Misalignment Spectrum :  Basically stated, angularity is the gap difference across two coupling faces-normally top to bottom or side to side. Angular misalignment in the radial direction Spectrum: Angular misalignment produces a bending moment o...
Read more

Commtest – Ascent Software Vibration Data Analyzed.

-
Image
  Commtest – Ascent Software Vibration Data Analyzed. If you are using a Commtest Vibration Analyzer and Ascent Software and require assistance or a second opinion on the analysis I am available to assist. Data can be sent to me via email. A fully written report will be presented to ISO 10816-7:2009 I provide expert vibration analysis and machinery diagnostics for Mining and other Industries. I have been a Vibration, Analyst for over 24 years and over 40 years in industrial maintenance with a proven track record. Robert is qualified for VA Level 111 and is a Condition Monitoring Technical Specialist. Robert has held roles as Maintenance Supervisor, Plant Inspector (Oil & gas) Predictive Systems Analyst, Reliability Supervisor, and Reliability Superintendent. Please contact if interested Contacts Email: robbieccs@gmail.com Alternative email: robertmva@yahoo.com.au
Read more

Autocorrelation Instructions for AMS Machinery Manager Version 5.5 or higher. Simply explained

-
Image
Autocorrelation Instructions for AMS Machinery Manager Version 5.5 or higher. Images from Emerson for demonstration purposes In this above example, we have two Acceleration Time Wave Forms (TWF) from two different machines. The first or top TWF is from a Blower inboard bearing in the vertical plane. The second is a cooling water centrifugal pump inboard bearing in the vertical plane. Notice in both TWF’s it is hard to detect if there is any repetitive impacting To Auto correlate, select the time waveform. In the above example, we click on the first TWF blower. Once selected then right-click – (see below Autocorrelation,) After the right-click the above menu box will appear. (Select Auto correlate. See results below) In this example for the blower, the autocorrelation is near 1 so the impacts are repetitive and is most likely related to a bearing defect. The second example below is a centrifugal cooling pump. Again, once the TWF is selected we again right-click and select autocorrel...
Read more